wifi mouse...

How to Connect a Wireless Mouse

Steps

Connecting to a Receiver

1. 1
   Insert the batteries into the mouse. Turn the mouse over, find the battery cover, and slide it off. Insert the appropriate batteries—usually two AAs.
   
   
   
   • The wireless receiver that plugs into the computer uses USB power, so it needs no batteries.
2. 2
   Connect the receiver to the computer. If your computer has a USB port (as most do), plug your receiver into an available port. There will also be a green adapter supplied, in the event that your system requires the use of the mouse port. Caution—don't try and force the mouse adapter into the keyboard port!
   
   
   
   • The mouse receiver has a USB plug (left), but can also plug into the mouse plug through the adapter it came with (right). If your receiver plugs into the USB port it should look like the left. If it plugs into the mouse plug it should look like the one on the right, only connected to the receiver.
3. 3
   Connect the mouse to the receiver. Place the mouse in close proximity to the receiver, and note the following:
   
   
   
   • The receiver should have a visible button that is easily pushable by the average human finger.
   • The mouse will usually have a very small reset button in a hole on the bottom that can be pushed by something like a pencil or paper clip.
   • Push both buttons at the same time with the receiver and the mouse relatively close to each other for about 5 seconds or more.
4. 4
   Find a permanent position the receiver. Place the receiver where it won't be far away from the mouse. Depending on where you are, you can place it on the monitor, on the tower, on the back of your laptop (if you are installing the mouse to your laptop) or on the desk.
   
   
   
   • The furthest a wireless mouse can get away from the receiver and still function is about 9 feet (2.7 meters), so keep that in mind.
5. 5
   Test your new mouse.
   
   
   
   • If you plugged into the mouse port, restart your computer.
   • If you plugged it into the USB port you should be able to use it immediately.
   • When the cursor moves when you move the mouse, you have connected the mouse properly. If the cursor doesn't move, try repositioning the receiver. If it still doesn't work, you may need to restart your computer (if you haven't already) or reconnect everything.
6. 6
   Adjust your mouse settings. Use the control panel that came with your wireless mouse, or download the necessary software from the manufacturer's website. Adjust the settings so that the mouse performs as you require.
   
   
   

Connecting Via Bluetooth

1. 1
   Insert batteries into your mouse. Turn your mouse over, locate the battery cover, and remove it. Insert the appropriate batteries—usually two AAs
   
   
   
2. 2
   Enable Bluetooth. In your Bluetooth control panel, make sure Bluetooth is turned on, and that your device is discoverable. (Refer to the device's user's guide for more information.)
   
   
   
   • Usually, the status LED on the mouse will blink when it's discoverable.
3. 3
   Discover the mouse. Set your Bluetooth setup control panel to discovery mode. It will search for available Bluetooth signals, then notify you when your mouse has been found.
   
   
   
   • Once the mouse has been discovered, follow the on-screen steps to finalize you setup procedure.
4. 4
   Adjust your mouse settings. Use the control panel that came with your wireless mouse, or download the necessary software from the manufacturer's website. Adjust the settings so that the mouse performs as you require.
   
   
   

Tips

• Clean off your desk before putting the mouse on. This way it will be easier to work with and make your desk look a little better.
• Try buying a mouse/keyboard combo pack. The mouse will match the keyboard, and the steps for setting up a keyboard are relatively the same as these.
• You can also create a dual-mouse hookup with a wireless USB mouse by plugging it into a USB port.
• Use a plug-in mouse during setup. It'll make the process smoother, and you'll still have control should something go awry during the setup. It's also good to have a wired mouse available in case your batteries die unexpectedly!
• Glue a 1 inch (2.5 cm) square of Velcro to the receiver and the place you are putting it. For best results, glue the hooks side of the Velcro (the hard side) to the receiver and the loops side of the Velcro (the soft side) to the surface.
• A mouse looks best if it blends in with its surroundings. The mouse should contrast themousepad, complement the keyboard, and match either the monitor or tower. The shape is also important. When you are picking one out, ask yourself "Will my hand be comfortable on this?" It is important to have a comfortable mouse, otherwise you could mess up when doing something that requires a steady hand (for example: designing graphics).